Our CECO Mefiag brand steel rubber-lined High Capacity Electroplating Filter Systems feature horizontal disc technology and capacities for Single Chamber up to 15,000 gph.

Designed for the filtration of nickel, copper and zinc electrolytes.
  • Operating temperature to 190 °F (90 °C).
  • Depending on the type of process, single chamber systems are designed for plating tanks up to 5,000 gallons.
  • Can be supplied with high profile (for zinc) or low profile (for nickel and copper) horizontal discs.
  • Special X-more
  • Unit of Measure

    Specifications

    Precoated Flow Rate (Filtering Capacity)

    15,000 gph

    Open Pumping Capacity

    18,000 gph

    Filtration Surface Area

    110 ft²

    Number of Filter Media

    44

    Filter Media Diameter

    22 "

    Sludge Holding Capacity

    3.62 ft³

    Length

    59 "

    Width

    44 "

    Height

    79 "

    Hose Connections Suction Discharge

    3 "

    Hose Length (Suction and Discharge)

    10 ft
    Motor1 10 HP Fybroc Series 1530

    Pump Options

    FYBROC 1530 Fiberglass Pump - Standard

    Slurry Tank Option

    NO SLURRY TANK - Standard WITH SLURRY TANK - Adder

    Weight

    1300 lbs

    Manufacturer

    Mefiag

    Features

    Features

    • Horizontal disc technology for greater surface area and maximum efficiency.
    • Large sludge holding capacity
    • Low disposal cost.
    • Wider range of flow rates for optimum bath turnover rates.
    • Corrosion resistant construction for use in most severe applications.
    • Temperatures to 190 °F (90 °C).
    • Mechanical lifting device for easy access to filter pack.
    • All polypropylene pump.
    • CRS mechanical seal with silicon carbide faces.
    • Powder coated steel frame with casters for easy handling.
    • Choice of cellulose, carbon/cellulose, and reusable polypropylene media.
    • NEMA 4 water tight, corrosion resistant starter.
    • Optional lifting device for easy pack removal

    Filter

    Filter

    Filter chambers are constructed of mild steel with hard rubber lining (3 mm) on the interior and corrosion resistant paint (2 coats) on the exterior.
    A flanged tangential inlet is standard, along with a bottom outlet and drain.
    Stainless steel eyebolts with handwheels hold the powder coated steel cover in place. The lifting device provides for mechanical movement of the cover for maintenance purposes.
    A pressure gauge (0-60 PSI) is supplied with a corrosion resistant guard.
    Filter media suited for the application is placed between the rigid polypropylene filter discs. Filter media of various materials and micron ratings are available. Ten (10) micron cellulose is standard.
    All systems are mounted on a powder coated structural steel frame with casters for easy handling.

    Pump

    Pump

    Polypropylene centrifugal pumps are equipped with TEFC, flange mounted motors. Mechanical seal is MEFIAG CRS-25/B with silicon carbide faces. Pump shaft is stainless steel. The motor starter is mounted in corrosion resistant, water tight NEMA 4 enclosure. The 15,000-LS Series, Fybroc fiberglass centrifugal pumps are standard. Mechanical seal options are single CRS- 35/B with silicon carbide faces or double water flush.

    Slurry Tank Specifications

    Slurry Tank Specifications

    Slurry tanks are mild steel construction with an interior of hard rubber (3 mm) and an exterior of corrosion resistant paint (2 coats). They are used to facilitate pre-coating and addition of activated carbon (if required), as well as solution make-up and priming of the pump. The slurry tank can also be used to store solution from the filter chamber during changing of media or maintenance.Pre-coating provides superior filtration and extends the lifeof the filter media.

    Piping, Valves and Connections

    Piping, Valves and Connections

    Piping, valves, and connections are all CPVC construction. Suction of the pump is piped to permit flow from the solution tank, slurry tank, and the filter chamber.

    X-Construction

    X-Construction

    X-construction is used for more aggressive solutions such as acid copper, acid zinc, and acid tin. The filter chamber and slurry tank are outside rubber lined, the base and cover are powder coated and the pump shaft is titanium.

    VD Lid Assembly

    VD Lid Assembly

    VD Lid assembly is used to tighten down the disc stack verses the cover. (Optional)
    • 1 Motor availability (Specify completely with order):
      2 HP or 3 HP -208, 230, 460, and 575 VAC (all 60 HZ, three-phase only)
      Fully-wired, liquid-tight motor starter with magnetic switch is included for proper thermal and overcurrent protection